Mackie Universal Remote HDR24 96 User Manual

R E M O T E 2 4  
USER’S GUIDE  
REMOTE CONTROL FOR THE  
HDR24/96 HARD DISK RECORDER  
 
Contents  
Take Management  
Features  
Installation  
4
Mount on Mic Stand  
9
(Optional) --------------------4  
Mount on Homemade Stand  
(Optional) --------------------4  
Plug It In ----------------------5  
Footswitch --------------------5  
Take Select -------------------9  
Track Select ------------------9  
Auto Take ---------------------9  
Meter --------------------------9  
Delete Last -------------------10  
Transport Features  
6
Current Time Display 10  
Play-----------------------------6  
Stop ----------------------------6  
Fast Wind ---------------------6  
Record -------------------------6  
Current Time -----------------10  
Other Stuff  
10  
Specifications ----------------10  
Troubleshooting &  
Record Features  
Record Ready ----------------7  
Record Safe-------------------7  
7
Warranty Service ------------11  
Colophon ---------------------12  
Monitoring Modes  
7
All Input-----------------------7  
Auto Input --------------------7  
Locator Features  
8
Locate -------------------------8  
Store ---------------------------8  
Loop ---------------------------8  
Punch --------------------------8  
Pre Roll ------------------------8  
Rehearse ----------------------9  
3
User Guide  
 
Rehearse  
Record Ready Pre Roll  
All Input  
HARD DISK RECORDER REMOTE CONTROL  
REMOTE 24  
1
2
3
4
5
6
7
8
9
10  
11  
12  
Assignable  
Meter  
13  
14  
15  
16  
17  
18  
1920  
21  
22  
23  
24  
TAKE  
TRACK NUMBER  
LOCATOR  
OL  
2
4
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Track  
-
7
-
Select  
10  
15  
20  
25  
30  
35  
40  
50  
-
AUTO  
TAKE  
(MINUTES)  
REC  
SAFE  
LOOP  
PUNCH  
PRE ROLL  
REHEARSE ALL INPUT  
(SECONDS)  
-
-
-
-
1
2
3
4
DELETE  
LAST  
-
AUTO  
INPUT  
TRACK SELECT  
TAKE SELECT  
Rec Safe  
LOCATE  
LOCATE  
STORE  
-
REWIND  
FAST FWD  
STOP  
PLAY  
RECORD  
Locate, Loop  
and Punch  
Transport  
Take Managment  
Auto Input  
Remote 24 with optional  
Atlas AD-11  
Installation  
Mount on Mic Stand (Optional)  
Mic stand adapters can make the  
Remote 24 seem like it's floating in  
midair! We recommend the Atlas  
model AD-11, available at your  
favorite music store. (If it's not, you  
need a new favorite music store.)  
Standard mic stand  
thread pitch  
Mount on Homemade Stand  
(Optional)  
(Top view) Optional  
Atlas AD-11 Surface  
Mount Adaptor  
The 3-hole pattern is equally spaced on a  
1.25" diameter circle. The holes accept three 6-32 x  
3/8 machine screws.  
Note: 3/8"  
maximum  
screw length!  
If you’re especially proud or ashamed of your  
handiwork, please mail us a photo.  
4
Remote 24  
 
Plug It In  
You can do this with the HDR24/96 powered on or powered off, it  
doesn’t matter.  
1. Plug the supplied 25' cable into the “To HDR” jack on  
the back of the Remote 24.  
2. Plug the other end into the “Remote” jack on the back of  
the HDR24/96.  
Footswitch  
A must-have for performer-engineers: use a footswitch to punch in  
and out on-the-fly, stop and start the transport, jump to the next  
cue, create new cues, or select the next take. The footswitch jack  
function is assigned in the  
Remote24 Back Panel  
HDR24/96 General Setup  
window. This TS 1/4" jack -  
and a jack on the back of  
the HDR24/96 - accepts a  
momentary, normally open  
footswitch, available at any  
reputable footswitch  
emporium. For double the  
fun, you can use  
footswitches in the Remote  
24 and HDR24/96 at the  
same time.  
TO HDR  
REMOTE JACK  
FOOT SW  
REMOTE 24  
WARNING  
DO NOT PLUG INTO  
ETHERNET  
Remote  
Cable  
DO NOT PLUG INTO  
NOT  
ETHERNET  
Footswitch  
FOOT  
SWITCH  
REMOTE  
MOUSE  
HDR24/96  
24TRACK 24 BIT DIGITAL AUDIO  
HARD DISK RECORDER/EDITOR  
Ethernet Jack  
WARNING  
DO NOT PLUG INTO  
ETHERNET  
FOOT  
SWITCH  
REMOTE  
MOUSE  
HDR24/96  
24TRACK 24 BIT DIGITAL AUDIO  
HARD DISK RECORDER/EDITOR  
Note: Do not  
confuse the  
VIDEO  
ACC  
1
SYNC  
ACC  
2
ETHERNET  
WA 98072 USA  
MIDI  
KEYBOARD  
CONCEIVED, DESIGNED, AND MANUFACTURED BY MACKIE DESIGNS INC  
WOODINVILLE  
MADE IN USA FABRIQUE AU USA  
PATENTS PENDING COPYRIGHT ©1998 THE FOLLOWING ARE TRADEMARKS OR  
REGISTERED TRADEMARKS OF MACKIE DESIGNS INC.: "MACKIE.", MACKIE DIGITAL SYSTEMS AND THE "RUNNING MAN" FIGURE.  
Remote jack  
with the  
120VAC  
50/60 Hz 475W  
CAUTION  
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT  
EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. DO NOT REMOVE COVER.  
NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.  
SERIAL NUMBER  
MANUFACTURING DATE  
WARNING: SHUT OFF POWER  
TO UNIT BEFORE INSTALLING  
OR REMOVING CARDS!  
RISK OF ELECTRIC SHOCK  
DO NOT OPEN  
AVIS: RISQUE DE CHOC ELECTRIQUE  
NE PAS OUVRIR  
OPT  
8
OPT  
8
OPT  
8
REPLACE WITH THE SAME TYPE FUSE AND RATING.  
DISCONNECT SUPPL CORD BEFORE CHANGING FUSE  
UTILISE UN FUSIBLE DE RECHANGE DE MÊME TYPE.  
DEBRANCHER AVANT DE REMPLACER LE FUSIBLE  
Y
Ethernet jack!  
HDR 24/96 Back Panel  
5
User’s Guide  
 
Transport Features  
REWIND  
FAST FWD  
STOP  
PLAY  
RECORD  
Play  
Play puts the HDR24/96 into play. Play also punches out of record  
and cancels master record standby.  
Stop  
Stop brings the “tape” to an immediate halt. Stop also punches  
out of record and cancels master record standby.  
Fast Wind  
REWIND  
FAST FWD  
Rewind and Fast Forward put the HDR24/96  
into fast wind mode from any state. They  
behave just like those on a large multitrack  
recorder: when pressed from stop, the “tape”  
rolls slowly at first, then accelerates to 20X  
speed in a few seconds. Pressing either button  
a second or third time puts the Transport into  
even faster wind speeds.  
Record  
PLAY  
RECORD  
Press Play and Record simultaneously to  
commence recording. Press any transport  
button except Record to end recording. The  
Record LED glows when recording and blinks  
when Record is engaged with no tracks armed  
(master record standby mode).  
6
Remote 24  
 
Record Features  
Record Ready  
Recording can only take place on tracks which are  
“armed” for recording. Press the Record Ready buttons to  
arm tracks. When Record is engaged, you can punch  
individual tracks in and out on the fly with the Record  
Ready buttons. Their LEDs blink in standby and glow in  
record.  
1
13  
Record Safe  
Record Safe disarms all tracks and disables the Record  
Ready and master Record buttons. Use Record Safe to  
prevent users from inadvertently recording over existing  
audio.  
REC  
SAFE  
Monitoring Modes  
The monitor mode buttons determine what the user hears at the  
HDR24/96 tape outputs.  
All Input  
All Input is used for rehearsal and level setting. When All  
Input is on, both armed and unarmed tracks monitor their  
tape inputs, and the Auto Input setting has no effect.  
ALL INPUT  
Auto Input  
Auto Input is used for recording, and affects only tracks  
that are armed. Unarmed tracks always monitor the  
playback of previously recorded audio.  
AUTO  
INPUT  
When Auto Input is off, armed tracks always monitor their  
tape inputs.  
When Auto Input is on, armed tracks monitor their tape inputs in  
stop, fast forward, rewind, and record; in play they monitor the  
playback of previously recorded audio. This mode is used for  
overdubbing.  
7
User’s Guide  
 
Locator Features  
Locate  
1
2
3
4
LOCATE  
LOCATE  
STORE  
Locate points provide fast access to frequently used locations in  
your project. Press one of the four Locate buttons to jump to a  
Locate point.  
Store  
To set a Locate point, press Store, then press a Locate  
button when the transport reaches the desired time.  
STORE  
Loop  
Locate 1 and Locate 2 double as start and end  
points for looped playback. To enable loop play,  
press Loop. Playback cycles between the two Loop  
points. The order of the Loop points does not  
matter.  
LOOP  
1
2
LOCATE  
Punch  
Locate 3 and Locate 4 double as in and out points  
for automated punching. To enable automated  
punching, press Punch. When you engage record,  
the HDR24/96 automatically punches in at the first  
Punch point, and punches out at the second. The  
order of the Punch points does not matter.  
PUNCH  
3
4
LOCATE  
Pre Roll  
Pre Roll causes a Locate to jump to a time that is earlier  
than the Locate time by the amount of the Pre Roll Time.  
Pre Roll is handy for autopunching, where you need to start  
playback a few seconds before the Punch in point. Pre Roll  
Time is set in the HDR24/96 MIDI Setup window.  
PRE ROLL  
8
Remote 24  
 
Rehearse  
Rehearse allows you to practice punching without  
actually recording anything to disk, saving you the hassle  
of deleting unwanted takes while monitoring and fine-  
tuning Autopunch points.  
REHEARSE  
Take Management Features  
TAKE  
TRACK NUMBER  
Take Select  
Each track has eight  
“virtual” takes that you can  
record to and play from.  
Take Select sets the active  
take for the selected track.  
AUTO  
TAKE  
(MINUTES)  
(SECONDS)  
DELETE  
LAST  
TRACK SELECT  
TAKE SELECT  
Track Select  
Use the Track Select  
buttons to select which tracks virtual take and meter information  
is shown in the Take and Meter displays; the selected track is  
shown in the Track Number display.  
Auto Take  
Auto Take automatically advances the Take Number of all armed  
tracks at the start of each record pass. When a tracks Take  
number reaches 8, it remains there until you change it.  
Tip: Use Loop and Punch with Auto Take to automatically  
record up to eight takes per track.  
OL  
2
4
7
10  
15  
20  
25  
30  
35  
40  
50  
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Meter  
-
The Meter displays the selected tracks input or  
playback level. On the Remote 24 and HDR24/96  
meters, 0 dB represents “full scale”, with no  
headroom to spare. Before recording, set the input  
level from your console as hot as possible.  
-
-
-
-
-
-
-
Audio levels must NEVER reach 0 dBFS….. ever!  
-
9
User’s Guide  
 
Delete Last  
Press the Delete Last button twice to erase the most  
recent recording pass from disk. A recording pass  
consists of all punches made within one play cycle. If you  
press Delete Last once then decide not to delete, wait five  
seconds and the operation will cancel.  
DELETE  
LAST  
Current Time Display  
Current Time  
TAKE  
TRACK NUMBER  
The Take and Track Number  
displays show Current Time  
whenever Play is held or the  
AUTO  
TAKE  
(MINUTES)  
(SECONDS)  
transport is in fast forward or  
rewind. Current Time also  
appears momentarily when Stop, Play or a Locate is pressed. An  
LED adjacent to the Take display blinks when current time is  
shown. Minutes in are shown in the Take display and Seconds in  
the Track Number display. Only the Minutes 'units' are visible; for  
example, if Current Time is '01:33:48:23', the display  
shows'3:48'.  
Other Stuff  
TO HDR  
REMOTE JACK  
FOOT SW  
REMOTE 24  
WARNING  
DO NOT PLUG INTO  
ETHERNET  
Specifications  
1.73  
W = 9.31" / 23.65 cm  
L = 6.44" / 16.36 cm  
H = 1.73" / 4.39 cm (high end);  
0.93" / 2.36 cm (low end)  
HARD DISK RECORDER REMOTE CONTROL  
REMOTE 24  
12  
1
2
3
4
5
6
7
8
9
10  
11  
Shipping weight: 4.0 lbs / 1.8 kg  
13  
14  
15  
16  
17  
18  
1920  
21  
22  
23  
24  
LOCATOR  
TAKE  
TRACK NUMBER  
OL  
2
4
7
10  
15  
20  
25  
30  
35  
40  
50  
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Supplied cable: CAT-5 Ethernet,  
25' / 7.6m  
Max cable length = 30' / 9.1m  
AUTO  
TAKE  
(MINUTES)  
REC  
SAFE  
LOOP  
PUNCH  
PRE ROLL  
REHEARSE ALL INPUT  
(SECONDS)  
-
9.31”  
-
-
-
1
2
3
4
DELETE  
LAST  
-
AUTO  
INPUT  
TRACK SELECT  
TAKE SELECT  
LOCATE  
LOCATE  
STORE  
-
REWIND  
FAST FWD  
STOP  
PLAY  
RECORD  
6.44”  
10  
Remote 24  
 
Troubleshooting & Warranty Service  
If you think your Remote 24 has a problem, try the following:  
Make sure the cable is plugged into the “Remote” jack on the  
rear panel of the HDR24/96 - the “Remote” jack is easy to  
confuse with the Ethernet jack.  
Remove and reinstall the cable, reboot the HDR24/96, and/or  
replace the Remote 24 cable (available at computer supply  
stores).  
Be sure you are not using a CAT-5 crossover cable (usually  
known by its yellow color and always labled “Crossover”).  
Put the Remote 24 into self-test mode and test the function of  
the swiches and LEDs.  
• Place a blank floppy disk into the HDR24/96 and power  
up the unit while holding down Record Ready buttons 1  
and 2 on the Remote 24.  
• When the unit is first powered on, all LEDs will be lit,  
and the Remote 24 firmware version number is shown in  
the Take and Track Number displays.  
• Pressing a button associated with an LED turns the  
LED off.  
• Pressing a Locate button lights the LED above it in the  
Locator section.  
• Pressing the Take Select buttons increments/  
decrements the Take and Track Number displays; and  
pressing the Track Select buttons increments/  
decrements the Meter display.  
After all this, if it still doesn’t work properly please contact Mackie  
Designs technical support at (800) 258-6883 (8:00 AM to 5:00 PM  
Pacific Time) - see the included Warranty Card for details.  
11  
User’s Guide  
 
Colophon  
This whopping opus was created by the HDR24/96 development  
team. Graphics and layout performed by Tony “waldog” Baird. No  
animals were injured in the production of this document, although  
Bob did feed Phydeaux some pretty old potato chips last week...  
“Mackie,” the “Running Man” figure, “HDR24/96” and “Remote  
24” are trademarks or registered trademarks of Mackie Designs  
Inc. All other brand names mentioned are trademarks or  
registered trademarks of their respective holders, and are hereby  
acknowledged.  
© 2000-2002 Mackie Designs Inc.  
All Rights Reserved.  
Printed in the U.S.A.  
®
12  
Remote 24  
 
Notes  
13  
User’s Guide  
 
Notes  
14  
Remote 24  
 
TO HDR  
REMOTE JACK  
FOOT SW  
REMOTE 24  
WARNING  
DO NOT PLUG INTO  
ETHERNET  
HARD DISK RECORDER REMOTE CONTROL  
REMOTE 24  
12  
1
2
3
4
5
6
7
8
9
10  
11  
13  
14  
15  
16  
17  
18  
1920  
21  
22  
23  
24  
TAKE  
TRACK NUMBER  
LOCATOR  
OL  
2
4
7
10  
15  
20  
25  
30  
35  
40  
50  
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
AUTO  
TAKE  
(MINUTES)  
REC  
SAFE  
LOOP  
PUNCH  
PRE ROLL  
REHEARSE ALL INPUT  
(SECONDS)  
-
-
-
-
1
2
3
4
DELETE  
LAST  
-
AUTO  
INPUT  
TRACK SELECT  
TAKE SELECT  
LOCATE  
LOCATE  
STORE  
-
REWIND  
FAST FWD  
STOP  
PLAY  
RECORD  
15  
User’s Guide  
 
16220 Wood-Red Rd. NE • Woodinville, WA 98072 • USA  
US & Canada: 800/898-3211  
Europe, Asia, Central & South America: 425/487-4333  
Middle East & Africa: 31-20-654-4000  
 

Lexmark Printer X730 User Manual
Lincoln Electric Welder IM10066 User Manual
Lindy Laminator 20975 User Manual
Lindy Switch H1TBELRG User Manual
Linksys Printer PPS1UW User Manual
Logan Graphic Products Brush Cutter 550 1 User Manual
Magnavox Blu ray Player MBP5220F User Manual
Makita Battery Charger DC1804 User Manual
Maytag Microwave Oven MMV5208WS User Manual
Merco Savory Toaster POP 2 4 User Manual